Jaffacakes Posted January 13, 2006 Report Share Posted January 13, 2006 I have got a back wheel that isn't really very true, and I was just wondering if anyone could give me any tips on how do it, it has got a strange wheel build which I can't really explain so here is a picture. It save's paying my LBS about £30 to do it.Cheers guys.And yes... I have an amazing camera . Quote Link to comment Share on other sites More sharing options...
Synergy Posted January 13, 2006 Report Share Posted January 13, 2006 not sure but can you not fix it with a spoke tool? Quote Link to comment Share on other sites More sharing options...
Jsy Ben Posted January 13, 2006 Report Share Posted January 13, 2006 Basic rule i folllow is:tighten spokes on the left and it will pull the rim over to the lefttighten spokes on the right and it will pull the rim over to the right just sit down turn your bike upside down or lean it vertical so its standing on your bars...and just spin your wheel...then spend time concentrating on your rim looking for what side it "buckles" to...hope you get your wheel true Quote Link to comment Share on other sites More sharing options...
tomturd Posted January 13, 2006 Report Share Posted January 13, 2006 Its radial one one side and 3 cross on the other...Read this -http://www.sheldonbrown.com/wheelbuild.html#tensioningDont worry about one side being radial and one 3 cross, it shouldnt really matter, basically tightening the spokes on the radial side will pull the rim over to the radial side of the hub, and vice versa - but theres a little more to it than that - read the link EDIT:Before I started using a spoke tensiometer, I used to keep a cassette in my toolbox on which I had recorded my piano playing an F#, a good average reference tone for stainless spokes of usual length.Just thought id highlight that for comical value. Quote Link to comment Share on other sites More sharing options...
Guest Posted January 13, 2006 Report Share Posted January 13, 2006 Yeh man my Rear wheel is like that too, I believe the non-drive saide is done 'Radially' but havn't a clue about the drive side.Regardless, all you need is a spoke key and the ability to find out where the buckle is. If the wheel bumps to the left every revolution, find the area that goes to the left and tighten the spokes connected to the right hand side of the hub(around the buckle), pulling the wheel true again.Best to do this in very small steps until you know exactley what your doing. Or if you can, do it on a friend's/siblings/shitty old wheel before you go destroying your wheelbuild.Does anyone know the reasons or advantages between differant spoke patterns? Quote Link to comment Share on other sites More sharing options...
wilky_mod_legend2 Posted January 13, 2006 Report Share Posted January 13, 2006 This is how i unbuckle my wheels.Stage 1Turn bike upside down, and put somefign were seat WOULD be, and spin wheel, look at the pads and you will be able to see where the buckle is.Stage 2Once you have found buckle, You will see that half the spokes are on 1 side of rim and the other half on the other side. So if the buckle is going to the right, tigten spokes on left, so it will pull wheel back into line. And if buckle goes other wise tigten spokes on the right.( turn a turn or half a turn at a time depending on how bad buckle is and how lose spoke is might have to turn it a load of times).Stage 3Spin wheel and check if its done anyfing if not repeat, if it has done something look at the rest of wheel and make sure that it hasnt put buckles any were else.Stage 4GO RIDEhope this helped cheers wilkydont think i missed anything out.Tools neededSpoke key Quote Link to comment Share on other sites More sharing options...
Jaffacakes Posted January 13, 2006 Author Report Share Posted January 13, 2006 Ok cheers guys I'll have a go at it now . Quote Link to comment Share on other sites More sharing options...
Sam Oliver Posted January 13, 2006 Report Share Posted January 13, 2006 My Dad & I recently tried to true my rear ti wheel but i think wemade it worse. Local bike shop did it perfect for only £7. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.