davey90 Posted February 28, 2010 Report Share Posted February 28, 2010 Hi, I have an old 2002 T-Pro frame, it has 4 bolt mounts but the centre to centre of the two bolt holes is 65.5mm whereas on my Woodstock the centre to centre of the two bolt holes is 55.5mm, are the older 4 bolt clamps still available for the larger mounts ? Quote Link to comment Share on other sites More sharing options...
Alex Dark Posted February 28, 2010 Report Share Posted February 28, 2010 Pciture please dude? sounds rather strange...they should all have been designed around the standard Magrua 4 bolt mount. Quote Link to comment Share on other sites More sharing options...
PeanuckleJive Posted February 28, 2010 Report Share Posted February 28, 2010 seems a bit odd that they're exactly 10mm wider apart, you didn't measure from a different point on the ruler and do the maths wrong did you? try measuring again Quote Link to comment Share on other sites More sharing options...
Alex Dark Posted February 28, 2010 Report Share Posted February 28, 2010 I bet you measured from the outside of each hole, instead of the middle of the holes? Quote Link to comment Share on other sites More sharing options...
Mike Poyzer @ Onza Posted February 28, 2010 Report Share Posted February 28, 2010 Are you sure they are not the dual fitting mounts which we fitted for a couple of years. They had an extra pair of holes in a groove in the well of the fitting. You then got a small alloy block with a hole in it which fitted either at the bottom of the slot if using a 20" back wheel or at the top of the slot if using a 19" back wheel. You then used an extra long bolt on that end. You cannot use the frame with Maguras without the little block. If you haven't got the blocks you are welcome to contact us if you cannot source them. Don't want to be accused of advertising. Quote Link to comment Share on other sites More sharing options...
Alex Dark Posted February 28, 2010 Report Share Posted February 28, 2010 (edited) Are you sure they are not the dual fitting mounts which we fitted for a couple of years. They had an extra pair of holes in a groove in the well of the fitting. You then got a small alloy block with a hole in it which fitted either at the bottom of the slot if using a 20" back wheel or at the top of the slot if using a 19" back wheel. You then used an extra long bolt on that end. You cannot use the frame with Maguras without the little block. If you haven't got the blocks you are welcome to contact us if you cannot source them. Don't want to be accused of advertising. Like on the old t-birds I'm sure the offset was more than ten mm? Edit: It would be 20 - 19" = 1" diameter...so 0.5" radius :. 12.25mm Edited February 28, 2010 by Alex Dark Quote Link to comment Share on other sites More sharing options...
davey90 Posted February 28, 2010 Author Report Share Posted February 28, 2010 Measured from centre to cenre on the holes and I used a steel rule so no dodgy ruler stuff going on, yeah there are holes in between the mounts aswell so it sounds like it is the dual fitting ones. Will email you about getting the blocks. Thanks for the help. Quote Link to comment Share on other sites More sharing options...
Alex Dark Posted February 28, 2010 Report Share Posted February 28, 2010 Measured from centre to cenre on the holes and I used a steel rule so no dodgy ruler stuff going on, yeah there are holes in between the mounts aswell so it sounds like it is the dual fitting ones. Will email you about getting the blocks. Thanks for the help. If not they're easy enough to make Quote Link to comment Share on other sites More sharing options...
davey90 Posted February 28, 2010 Author Report Share Posted February 28, 2010 If not they're easy enough to make Is it just a standard bit of alloy block with a hole it it ? If so i could probably make it in uni. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.