Jack Morton Posted April 17, 2009 Report Share Posted April 17, 2009 As the title say's i need to get intouch with Magura I've looked round there website, A countless amount of time's and never so far found a email address. So wanted to no if anyone knew where i could find the email address for them or maybe you even have it.Help would be aprishiatedSorry for any spelling mistakesJack Quote Link to comment Share on other sites More sharing options...
Luke_zoo Posted April 17, 2009 Report Share Posted April 17, 2009 Why do you need to get Intouch with them what about ?Maybe we could help on here. Quote Link to comment Share on other sites More sharing options...
Jack Morton Posted April 17, 2009 Author Report Share Posted April 17, 2009 Well my lever cracked. Not on the clamp bit, On the back of it between where the lever bolt's in and the clamp And i wanted to no if they would do a half price replacement Cause i didnt bash it / fall of anything along them lines i was hoping of a wall when i noticed it. Quote Link to comment Share on other sites More sharing options...
Luke_zoo Posted April 17, 2009 Report Share Posted April 17, 2009 Buy a new one from tartybikes job done.Proberly tightend the leaver bolt too tight so it's cracked. Quote Link to comment Share on other sites More sharing options...
Muel Posted April 17, 2009 Report Share Posted April 17, 2009 Or, get in touch with Magura, and see if he can get one cheaper...I doubt they'll warrenty it though to be honest mate, it's obvious that it has had a few knocks. Quote Link to comment Share on other sites More sharing options...
Jack Morton Posted April 17, 2009 Author Report Share Posted April 17, 2009 Never over tightented the bolt . Well only once when i first took the lever out and the lever didn't come back out. After that never againWell it's worth a shot before going and buying a new one. Anyways getting back ontopic does anyone have contact detail's for magura. Quote Link to comment Share on other sites More sharing options...
Luke_zoo Posted April 17, 2009 Report Share Posted April 17, 2009 Or, get in touch with Magura, and see if he can get one cheaper...I doubt they'll warrenty it though to be honest mate, it's obvious that it has had a few knocks.True but If you got them from tartybikes may as well just buy a set ? at the LBS it's £30-£40ish for a pair of magura leaver and body.From tartybikes.Magura LogoMagura HS33 Lever, 2005From £39.15 to £44.04 Maximum torque for handlebar clamp bolt is 4Nm. Over tightening this bolt may cause the lever assembly to break and this is not covered under warranty.T@RTYB!KES Quote Link to comment Share on other sites More sharing options...
Muel Posted April 17, 2009 Report Share Posted April 17, 2009 Are you going to help or not? It's worth a try, all he needs is an Email address. If you don't know it, don't post. Quote Link to comment Share on other sites More sharing options...
Jack Morton Posted April 17, 2009 Author Report Share Posted April 17, 2009 Are you going to help or not? It's worth a try, all he needs is an Email address. If you don't know it, don't post.Thank's for saying that i wanted to say it so much but didnt want to come across as being all rude. Quote Link to comment Share on other sites More sharing options...
Ali C Posted April 17, 2009 Report Share Posted April 17, 2009 you can try it, but I have seen less scratched levers refused warranty! Quote Link to comment Share on other sites More sharing options...
Luke_zoo Posted April 17, 2009 Report Share Posted April 17, 2009 magura ...Try that then. Quote Link to comment Share on other sites More sharing options...
Jack Morton Posted April 17, 2009 Author Report Share Posted April 17, 2009 (edited) When signing up it doesn't give you the choice of United Kindom.But thank's anyways. Edited April 17, 2009 by jackm9863 Quote Link to comment Share on other sites More sharing options...
monkeyseemonkeydo Posted April 17, 2009 Report Share Posted April 17, 2009 Venhill used to be/are the UK importers for Magura and deal with warranty claims. However, 05 Magura's levers will crack at that point simply due to it being poorly designed. If and when you get a replacement lever, take a dremel and round off that corner to remove the stress riser which causes levers to crack when used for trials. Or at least wait until the lever starts to crack then attack it with a Dremel which is what I've done.Edit:www.venhill.co.ukinfo@venhill.co.ukVenhill Engineering Ltd21 Ranmore RoadDorkingSurreyRH4 1HE01306 885111 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.