Azarathal

Pretty sure I saw those listed on eBay with dead bearings in the rear hub, still a bargain by all regards even if I did need to do bearings. Just tried my luck at bending the hangar / mech back, I now only have 2 and 7-9 but at least they index a touch better, I did get it working going from 9 down to 5 but then had too much tension to drop one gear at a time. Thinking about what I'd need to do to get this bike to a decent standard I may just slap some skinny road tyres on and upgrade bikes when I'm earning

Thanks for the reply, amazed to see you're still about here! Forks will be when I'm back in work (I'm hoping very soon) so when some money is coming in I may take you up on those forks! Front wheel will more than likely wait until forks (if I can tighten the cones), as you've mentioned the difference between 9mm QR, bolt through etc. Mountain kings haven't been too bad to me! When run at 20psi anyway... Frame is for 26" wheels, 9mm QR all round, 3x9 but would go 1x9 as I never really leave the bigger front ring. Not sure on ratios but as it is they're shit due to bent mech. Would it make sense if I said the bike feels sluggish? Almost like even on flat smooth surfaces I'm peddaling through grass, clay etc and I pretty much have to be constantly on the pedals even during the downhill sections

Hey guys, don't think I've been on here since the 2016 Trials forum track day? Been a while anyway so hope everyone is good! I've got a 2012 Saracen Mantra Trail, not they best but for what I paid it's been perfect. Now I've done a few trails around Swinley Forrest (30+ miles in the last week) I'm going to be needing to upgrade some bits ASAP. The trails are over a rough stone floor with loose stones, drops, roots etc as well. The headset, F+R hub cones and even front derailure have vibrated loose, my rear mech is bent and the stancion seals are worn giving the forks a lot of play. I'm after the cheapest upgrades possible, secondhand is prefered and eBay links even better! I'll stick the spec below and If anyone can lend a hand It'd be great. Saracen Mantra Trail 2012 frame Suntour XCR LO 120mm travel 1 1/8th non tapered (Can I spin the stancion seals 90degrees so the play is left to right?) Acera front mech Deore rear (hangar bent, cage is twisted) Shimano M445 brakes 180/160, these are faultless except the odd bit of fade Formula unsealed hubs, pretty sure both axles are bent and the cones keep coming loose, notchy af Continental Mountain king 2.2, sidewalls are wearing thin. Thanks!

So spoiler cost me £90, bonnet was a straight swap for my oem steel bonnet, not bad if I say so, just needs a bit of paint

Standard is "276" Hp because some stupid regulations. Yeah I did in the end, never again

Should hopefully be dropping it off tomorrow to have the gearbox replaced with a fully reburbed box and having it mapped, auto ecu has flat spots and it's running like shit. finally got the front mount on, no matter what I do I can't get the Intercooler central so the bumper can't sit properly and there's a boost leak but I've triple checked everything and all clamps are tight with a good seal

So I tried fitting my fmic yesterday and had to give up at 10pm because angle grinding in the dark is not the one. So far I've trimmed about 10mm from the bumper support, much more from the bumper itself and I've still got to cut a hole in my inner wing to run pipework. I've also had to turn the horns around, trim my a/c fan cover and re locate my temp sensor Has anyone got a spare will to live?

Quite a few bits I need sorting namely bushes and bracing, car was waaaay too sloppy yesterday, could probably do with some decent tyres too

Brilliant day! Thanks Dan for organising it, I think the wet laps were my favourite for certain reasons

On route but getting bummed by traffic

Sucks to hear that mate give me a shout when you're back and we'll go for a run out, you've gotta show me some of the decent routes around fleet at some point

But surely he'll be coming in his pimp as f**k fiat? Haz I'll bring a scissor jack? Or if you wanted to convoy with me (if you're still around Crowthorne) I've got a hydraulic jack you could use before we go

I f**king love that number plate

Got my spoiler on, not a perfect fit and needs paint so I'll let a body shop fettle and paint it, not bad for some 22 year old suspension and £90 in cash